{"id":1487,"date":"2015-03-15T18:41:20","date_gmt":"2015-03-16T02:41:20","guid":{"rendered":"http:\/\/www.billdugan.com\/scout\/?p=1487"},"modified":"2021-11-23T08:30:56","modified_gmt":"2021-11-23T16:30:56","slug":"project-pt-cruiser-seats","status":"publish","type":"post","link":"https:\/\/www.billdugan.com\/scout\/2015\/03\/15\/project-pt-cruiser-seats\/","title":{"rendered":"Project: PT Cruiser Seats"},"content":{"rendered":"

To recap:<\/em> In early January, I pulled two gray cloth seats from a junkyard 2004 PT Cruiser. All it took was a 13 and 11mm box wrench, and one disconnect for the seatbelt sensor. They aren’t light, but they’re lighter than seats from a 2001 model, which had integrated side airbags.<\/p>\n

\"PT<\/a><\/p>\n

These have built-in side armrests that fold up out of the way. They interfere with the placement of my Tuffy console, so I’ll be removing them. The female side of the seatbelt is integrated into the side of the seat, so that will need to come off as well.<\/p>\n

The slider rails are held together with a plate in the back. They are longer than stock Scout bases, but the width of the rails is perfect. Originally, I thought I was going to have to build extender plates for each of the bases to reach the front mount points because I was sure I wouldn’t be able to get bolts to fit in between the slider rails. When I really looked it over, though, I realized I was going to have to drill a hole for a bolt between the rails anyway. I picked up some grade 8 stock and test fit everything to check the clearances, and it worked perfectly.<\/p>\n

\"Side<\/a><\/p>\n

Here’s where the plastic comes off. a T50 Torx bit will remove the seatbelt anchor.<\/p>\n

\"IMG_0110\"<\/a><\/p>\n

On the side, pry the cap off with a flathead screwdriver. A T45 bit will take off the armrest and a standoff that locks the arm into place. The driver’s side is backed with plastic, so the seat doesn’t look bad with the armrest gone. The passenger’s side doesn’t have it.<\/p>\n

\"IMG_0112\"<\/a><\/p>\n

I’ve been using a spare set of bases to mock things up on, but they are both rusted at the bottoms enough that I wouldn’t put them back in service without welding in some serious support. I took a second look at the bases I had, with tracks welded to the top, and decided to try a little surgery with an angle grinder.<\/p>\n

\"IMG_0164\"<\/a><\/p>\n

\"IMG_0130\"<\/a> \"IMG_0140\"<\/a><\/p>\n

After some careful cutting I got the tracks off and ground the edges off to a smooth surface, then sanded all surface rust and scale off. Then I wiped everything down with acetone to clean off any oil or grease.<\/p>\n

\"IMG_0120\"<\/a><\/p>\n

To attach the bases to the tracks, I used the stock bolts from the seat in the rear. There are two threaded bolt holes in the back. I used the one closest to the front, then marked the holes for the front bolts and drilled them. Then I used a set of 3\/8″ x 1″ Grade 8 bolts threaded in from above to attach the front of the seats to the tracks. The seats slide cleanly.<\/p>\n

\"IMG_0122\"<\/a><\/p>\n

 <\/p>\n

\"IMG_0205\"<\/a><\/p>\n

The project got sidelined for a week while I waited for Eastwood to send me rust converter. I used a brush to put it on, but the next time I’m at Target I’m going to pick up a cheap spray bottle for application\u00e2\u20ac\u201cit’s much easier that way. I hit everything I could see and let it sit for 48 hours.<\/p>\n

\"IMG_0210\"<\/a><\/p>\n

Then all the bare metal got a coat of etching primer and two coats of Rustoleum satin black.<\/p>\n

\"IMG_0218\"<\/a><\/p>\n

Then I attached the seats back on the bases and put the bases back into my Scout. Compared to 30-year-old Chrysler seats, 10-year-old Chrysler seats feel like they just rolled off the factory floor, even if they don’t exactly match the rest of the truck\u00e2\u20ac\u201cbut then, nothing<\/em> matches on this truck.<\/p>\n

Postscript:<\/em> One other nice feature is the fact that the passenger seat folds completely forward. So transporting 10′ boards without resting them on the fabric cover of the console is easy.<\/p>\n

\"img_2985\"<\/p>\n","protected":false},"excerpt":{"rendered":"

To recap: In early January, I pulled two gray cloth seats from a junkyard 2004 PT Cruiser. All it took was a 13 and 11mm box wrench, and one disconnect for the seatbelt sensor. They aren’t light, but they’re lighter than seats from a 2001 model, which had integrated side airbags. These have built-in side […]<\/p>\n","protected":false},"author":1,"featured_media":0,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"_jetpack_newsletter_access":"","_jetpack_dont_email_post_to_subs":false,"_jetpack_newsletter_tier_id":0,"_jetpack_memberships_contains_paywalled_content":false,"_jetpack_feature_clip_id":0,"_jetpack_memberships_contains_paid_content":false,"footnotes":"","jetpack_post_was_ever_published":false},"categories":[64,50],"tags":[],"class_list":["post-1487","post","type-post","status-publish","format-standard","hentry","category-junkyards","category-seats"],"jetpack_shortlink":"https:\/\/wp.me\/p58Ac2-nZ","jetpack_sharing_enabled":true,"jetpack_featured_media_url":"","_links":{"self":[{"href":"https:\/\/www.billdugan.com\/scout\/wp-json\/wp\/v2\/posts\/1487","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.billdugan.com\/scout\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.billdugan.com\/scout\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.billdugan.com\/scout\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/www.billdugan.com\/scout\/wp-json\/wp\/v2\/comments?post=1487"}],"version-history":[{"count":12,"href":"https:\/\/www.billdugan.com\/scout\/wp-json\/wp\/v2\/posts\/1487\/revisions"}],"predecessor-version":[{"id":1676,"href":"https:\/\/www.billdugan.com\/scout\/wp-json\/wp\/v2\/posts\/1487\/revisions\/1676"}],"wp:attachment":[{"href":"https:\/\/www.billdugan.com\/scout\/wp-json\/wp\/v2\/media?parent=1487"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.billdugan.com\/scout\/wp-json\/wp\/v2\/categories?post=1487"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.billdugan.com\/scout\/wp-json\/wp\/v2\/tags?post=1487"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}